 |
 |
 |
|
VWR Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack
The VWR Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack, Model #'s: 51014992 provides the selection, performance, and quality needed in today's cell culture laboratory. This CO2 Incubator Dual Stack offers two levels of security for your valuable cell cultures. HEPA filtration safeguards your cultures from airborne contaminants, the primary source of contamination in the lab, along with featuring a high heat sterilization cycle. This on-demand sterilization cycle provides a 12 hour cycle of heat at 140C that eliminates contamination from internal surfaces, allowing for easy cleaning and reliable decontamination. This dual stack unit combines precise temperature and CO2 control with the use of a thermal conductivity (T/C sensor), making the VWR Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack an optimal choice for many different laboratory and cell culture applications.
All of our equipment is fully tested to perform at factory
specifications before being shipped.
The VWR Symphony Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack, includes:
- > 6 x Shelves
- > 2 x Humidity Pans
- > 2 x New HEPA Filters
- > Calibration and Preventative Maintenance Report
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
VWR Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack Specifications
|
Temperature:
|
|
|
Control
|
0.1C
|
|
Temperature Range
|
Ambient +5C to 50C
|
|
Temperature Uniformity
|
0.3C at 37C
|
|
Tracking Alarm
|
User programmable (low) indicator
|
|
Overtemperature
|
Tracking, user programmable, action, and indicator
|
|
Display
|
Digital LED
|
|
CO2:
|
|
|
CO2 Control
|
0.1%
|
|
CO2 Range
|
0-20%
|
|
Inlet Pressure
|
15 psig (1 bar)
|
|
CO2 Sensor
|
T/C
|
|
Readability
|
0.1%
|
|
Display
|
Digital LED
|
|
Humidity:
|
|
|
RH
|
95% RH at 37C
|
|
Control
|
N/A - natural vaporization
|
|
Temperature Safety:
|
|
|
Type
|
Extreme temperature safety, action, and indicator
|
|
Sensor
|
Thermostat, independent of temp control system
|
|
Indicator
|
Message center, audible and visual alarms
|
|
Construction:
|
|
|
Interior Volume
|
6.5 cu ft. (184L) per unit
|
|
Interior Dimensions (W x H x D)
|
21.3 x 26.8 x 20 in (54 x 68.1 x 50.8 cm)
|
|
Exterior Dimensions (W x H x D)
|
26.1 x 39.5 x 25 in (66.3 x 100.3 x 63.5 cm)
|
|
Insulation
|
Mineral wool
|
|
Outer Door Gasket
|
Four-sided molded, magnetic santoprene
|
|
Inner Door Gasket
|
Bulb, silicone
|
|
Weight
|
260 lbs (118 kg)
|
|
Electrical Requirements
|
115V, 50/60Hz, 9.6A, 1PH
|
VWR Air Jacketed CO2 Incubator w/ Sterilization Cycle Dual Stack Manual
 Click Here to View the Technical Specs for the VWR Air Jacketed CO2 Incubator
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Inspect display for dim, flickering, or dead pixels; replace for readability
|
Completed
|
|
|
Examine external regulators for damage or malfunction; replace compromised parts
|
Completed
|
|
|
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy
|
Completed
|
|
|
Inspect internal wiring for frays, tears, or breakages; replace compromised wires
|
Completed
|
|
|
Verify software settings align with components and calibration specs; adjust if needed
|
Completed
|
|
|
Clean fan and remove dust/obstructions; replace if performance is substandard
|
Completed
|
|
|
Examine wheels and leveling mounts for structural integrity and balance
|
Completed
|
|
|
Inspect door gaskets and latches for wear or damage; replace to maintain seal
|
Completed
|
|
|
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy
|
Completed
|
|
|
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision
|
Completed
|
|
|
Monitor temperature and CO₂ stability over 24-hour period to verify consistency
|
Completed
|
|
|
Conduct cosmetic inspection to confirm quality of external surfaces and components
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
