 |
 |
 |
|
Thermo Scientific LP Vortex Mixer
Maximum Speed
0 to 3,000 RPM
Speed Control Type
Adjustment Knob
- Features a brushless, maintenance-free motor, ensuring long-lasting, reliable performance
- 10 programmable acceleration and deceleration ramps for simplified operation
- Compatible with a variety of rotors to ensure adaptability across required sample volumes and speeds
- Functions as three centrifuges in one: high-capacity, high-speed, and microcentrifuge
- Offers a wide range of applications, from cell harvesting to DNA precipitation
- Includes a timer with settings from 1 to 99 minutes, plus a continuous mode
The Thermo Scientific LP Vortex Mixer is a compact, low-profile mixing solution designed to handle a wide range of laboratory applications. With a speed range of 0 to 3,000 RPM and the flexibility to operate in continuous or touch modes, this vortex mixer provides reliable and efficient mixing for tubes, plates, and glass vessels. Its small footprint (6.1 x 8.3 x 3.3 inches) and lightweight design (6.8 lb.) make it an ideal choice for labs with limited space.
Built with user safety in mind, the LP Vortex Mixer features current overload protection and accommodates various vessel types through optional accessories. Operating on 100–240V, 50/60 Hz, it ensures consistent performance for applications requiring effective vortex mixing.
All of our equipment is in excellent condition and will be fully tested to perform at factory specifications before being shipped.
The Thermo Scientific LP Vortex Mixer includes:
- > Rubber Dimpled Head
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Thermo Scientific LP Vortex Mixer Specifications
|
Speed Range
|
0 to 3,000 RPM
|
|
Speed Setting/Display
|
Analog
|
|
Speed Control Type
|
Adjustment Knob
|
|
Orbit
|
4 mm
|
|
Timer
|
N/A
|
|
Operating Mode
|
Touch, Continuous, High-Continuous
|
|
Motor Rating Input (W)
|
12
|
|
Motor Rating Output (W)
|
6
|
|
Motor Type
|
BLDC (Brushless Direct Current) Motor
|
|
Drive System
|
Eccentric Drive & Support Arm with Vibrating Motion
|
|
Permissible Relative Temperature (°C)
|
+5 to 40°C
|
|
Max. Load
|
1.1 lb. (0.5 kg)
|
|
Permissible Relative Humidity
|
80%
|
|
Safety Device
|
Self-Resetting/Current Limit Protection
|
|
Protection Class acc. to DIN EN 60529
|
IP 42
|
|
Body Material
|
Polypropylene
|
|
Rubber Platform Material
|
Silicone Rubber
|
|
Exterior Dimensions
|
6.1 x 8.3 x 3.3 in. (15.4 x 21 x 8.3 cm)
|
|
Weight
|
6.8 lb. (3.1kg.)
|
|
Electrical Requirements
|
100 - 240V, 50/60 Hz
|
- Verify power supply and PCB output correct, stable voltages across all required circuits
- Confirm the correct platform head is installed according to specifications
- Inspect the display for dim or dead pixels, replacing any compromised sections to maintain clear visibility
- Confirm full functionality of all buttons and knobs, ensuring accurate input response
- Verify that touch, pulse, and continuous modes operate fully and as intended
- Inspect all internal wiring for breakages, tears, or wear, replacing any underperforming components to ensure reliability
- Disassemble and thoroughly clean the internal casing to remove any accumulated debris
- Check that the feet are intact and confirm the vortexer is properly balanced on a flat surface
- Conduct a comprehensive cosmetic inspection to ensure all exterior surfaces meet quality standards
Technician Inspection and Recertification Checklist: Vortexer
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Verify power supply and PCB output stable, correct voltages across circuits
|
Completed
|
|
|
Confirm correct platform head is installed according to specifications
|
Completed
|
|
|
Inspect display for dim or dead pixels; replace compromised sections for clarity
|
Completed
|
|
|
Confirm functionality of all buttons and knobs for accurate input response
|
Completed
|
|
|
Verify full operation of touch, pulse, and continuous modes as intended
|
Completed
|
|
|
Inspect internal wiring for damage; replace underperforming components for reliability
|
Completed
|
|
|
Disassemble and clean internal casing to remove accumulated debris
|
Completed
|
|
|
Check feet for integrity and confirm vortexer is balanced on flat surface
|
Completed
|
|
|
Conduct comprehensive cosmetic inspection to ensure quality of exterior surfaces
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
