 |
 |
 |
|
Thermo Scientific ALPS30 Manual Microplate Heat Sealer
Sealing Temperature Setpoint
170°C
Plate Compatibility
96-Well,384-Well, and 96-Well Skirted PCR Plates
Sealing Temperature Accuracy
± 2ºC
- Manual, hand-operated design supports quick and efficient sealing for routine laboratory workflows
- Consistent heat sealing helps protect samples from evaporation and contamination
- Compatible with a wide range of Thermo Scientific heat seal formats
- Built-in thermostat helps prevent overheating during operation
- Automatic safety shutoff supports reliable daily use
- LED indicators clearly show power and heating status
- Small, lightweight construction allows easy portability
- Compact bench-friendly design supports convenient everyday access
The Thermo Scientific ALPS30 Manual Microplate Heat Sealer is a compact, hand-operated solution designed to protect samples from evaporation and contamination during microplate processing workflows. Built for low- to medium-throughput applications, the ALPS30 delivers consistent, reliable heat sealing while remaining small enough to stay on the bench without occupying valuable workspace. Its manual operation is straightforward and ergonomic, allowing users to seal plates quickly and efficiently as needed.
Designed for flexibility, the ALPS30 is compatible with a wide range of Thermo Scientific heat seals, including pierceable, optically clear, and permanent formats. The unit accommodates a variety of microplate heights and PCR plates, and this configuration includes adapters for 96-well, 384-well, and 96-well skirted PCR plates. A built-in thermostat helps prevent overheating, supporting safe and consistent operation, while LED indicator lights clearly show power and heating status. Lightweight construction and a small footprint make the Thermo Scientific ALPS30 Manual Microplate Heat Sealer easy to move and convenient to keep within reach for everyday laboratory use.
Please Note: Sealing films and foils are required for operation and not included with purchase of the Thermo Scientific ALPS30 Manual Microplate Heat Sealer.
All of our equipment is fully tested to perform at factory specifications before being shipped.
The Thermo Scientific ALPS30 Manual Microplate Heat Sealer
includes:
- > 96 and 384-Well Adapter Block
- > Power Cord
- > Full 180 Day Parts and Labor Warranty
Thermo Scientific ALPS30 Manual Microplate Heat Sealer
Specifications
|
Sealing Temperature Setpoint
|
170°C
|
|
Sealing Temperature Accuracy
|
± 2°C
|
|
Plate Compatibility (w/ Included Adapter Block)
|
96-Well,384-Well, and 96-Well Skirted PCR Plates
|
|
Dimensions (W x D x H)
|
8.7 x 9.8 x 9.1 in. (22 x 25 x 23 cm)
|
|
Weight
|
8.8 lb. (4 kg)
|
|
Electrical Requirements
|
120V, 60Hz
|
- Install new waste and buffer bottles to ensure proper fluid containment and system functionality.
- Integrate a new pump into the system, verifying compatibility and secure connections.
- Verify that the power supply and PCB output the correct voltages for reliable component operation.
- Conduct a self-test on the microplate washer, evaluating all operational parameters.
- Inspect the X-axis motor belt for signs of wear, such as tears, frays, or breakages, replacing if necessary.
- Examine dispense and aspirate tubes for any damage that could affect fluid flow accuracy.
- Confirm internal pump functionality, replacing seals as needed to maintain optimal performance.
- Inspect all internal wiring for frays, tears, or breakages, addressing any faults for electrical safety.
- Verify functionality of all internal and external sensors, ensuring accurate readings across the unit.
- Disinfect the unit using an appropriate disinfection cycle to ensure sterility and safety.
- Check that residual aspiration levels are within the manufacturer’s specified limits for accuracy.
- Conduct a final cosmetic inspection to verify that all external surfaces meet appearance standards.
Technician Inspection and Recertification Checklist: Microplate Washer
The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment
| Task |
Completed? |
Remarks? |
| Install new waste and buffer bottles | Completed | |
| Integrate new pump into system, verifying secure connections | Completed | |
| Verify power supply and PCB output correct voltages | Completed | |
| Conduct microplate washer self-test and evaluate results | Completed | |
| Inspect X-axis motor belt for wear, replacing if necessary | Completed | |
| Examine dispense and aspirate tubes for any damage | Completed | |
| Confirm internal pump functionality, replace seals as needed | Completed | |
| Inspect internal wiring for frays, tears, or breakages | Completed | |
| Verify functionality of all internal and external sensors | Completed | |
| Disinfect unit with appropriate disinfection cycle | Completed | |
| Check residual aspiration levels meet specifications | Completed | |
| Conduct cosmetic inspection for appearance standards | Completed | |
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
