 |
 |
 |
|
Panasonic MCO-170AICUVL-PA CO2 Incubator
Temperature Range
Ambient +5°C to 50°C
- Keypad controls with arrow keys allow precise setpoint adjustments in 0.1°C increments
- Red LED display clearly shows temperature readouts and control parameters
- LED indicators alert users to heater power status, error conditions, or active settings
- Durable enamel-coated steel exterior with stainless steel chamber construction
- Low-watt-density heater elements reduce maintenance and extend service life
- Built-in safety backup maintains control if primary heater fails, with LED alarm notification
The Panasonic MCO-170AICUVL-PA CO2 Incubator’s delivers exceptional ease of use, effortless cleaning and maintenance as well as outstanding performance with a temperature range from Ambient +5°C to 50°C. The patented Direct Heat and Air Jacket system works with the IR2 sensor to provide precise temperature and CO2 levels, respectively. The included Incu-Safe and SafeCell UV features function together to control contamination. The Incu-Safe copper enriched, stainless-steel alloy offers germicidal properties of elemental copper without corrosion or discoloration, while the SafeCell isolated UV lamp decontaminates circulated air and the humidity water reservoir without harming the cultured cells. A color LCD touchscreen delivers full control, even with gloved hands, while a standard USB port makes log data transfer to PC convenient. This Control panel interface allows for easy programming of temperature, CO2 and other internal conditions of the incubator. The CO2 incubator offers integrated shelf channels with minimal parts for easy cleaning. The proprietary Dual Filter IR sensor achieves ultrafast CO2 recovery without overshooting, even following multiple door openings. This incubator also features multiple different alarms for power failure, temperature deviation, gas deviation, empty gas supply, and open door. The MCO-170AICUVL-PA is designed for demanding and regulated applications in biomedical, pharmaceutical, medical research and clinical laboratory applications.
All of our equipment is fully tested to perform at factory specifications before being shipped.
The Panasonic MCO-170AICUVL-PA CO2 Incubator includes:
- > UV Lamp
- > 2 Shelves
- > Humidity Pan
- > NIST Calibration and Preventative Maintenance Report
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Panasonic MCO-170AICUVL-PA CO2 Incubator Specifications
|
Temperature Range
|
Ambient +5°C to 50°C
|
|
Temperature Uniformity
|
± 0.25°C at 37°C
|
|
Temperature Stability
|
± 0.1°C
|
|
Temperature Sensor Type
|
Thermistor
|
|
CO2 Range
|
0 to 20%
|
|
CO2 Control Stability
|
± 0.15%
|
|
CO2 Sensor Type
|
Dual Filter IR
|
|
Required Gas Pressure
|
0 to 15 psi
|
|
Relative Humidity
|
95% ±5% at 37°C
|
|
Volume
|
5.8 cu. ft. (165L)
|
|
Display
|
Color LCD touchscreen readable to 0.1 increments
|
|
Alarms
|
Power failure, temperature deviation, gas deviation, supply empty, and door open
|
|
Access Port Diameter
|
1.2 in. (30 mm)
|
|
Internal Dimensions (W x H x D)
|
19.3 x 20.6 x 26.2 in. (49 x 52.3 x 66.5 cm)
|
|
External Dimensions (W x H x D)
|
24.4 x 28.7 x 35.6 in. (62 x 73 x 90.5 cm)
|
|
Weight
|
176 lb. (80 kg.)
|
|
Electrical Requirements
|
110-120V, 60 Hz, 3.4A, 376W
|
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Inspect display for dim, flickering, or dead pixels; replace for readability
|
Completed
|
|
|
Examine external regulators for damage or malfunction; replace compromised parts
|
Completed
|
|
|
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy
|
Completed
|
|
|
Inspect internal wiring for frays, tears, or breakages; replace compromised wires
|
Completed
|
|
|
Verify software settings align with components and calibration specs; adjust if needed
|
Completed
|
|
|
Clean fan and remove dust/obstructions; replace if performance is substandard
|
Completed
|
|
|
Examine wheels and leveling mounts for structural integrity and balance
|
Completed
|
|
|
Inspect door gaskets and latches for wear or damage; replace to maintain seal
|
Completed
|
|
|
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy
|
Completed
|
|
|
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision
|
Completed
|
|
|
Monitor temperature and CO₂ stability over 24-hour period to verify consistency
|
Completed
|
|
|
Conduct cosmetic inspection to confirm quality of external surfaces and components
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
