Stock Notification!

The Labconco Freezone 18L Freeze Dryer System you were interested in is currently unavailable, but we have a great alternative for you!

Our Price: $19,830.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days

Request a Formal Quote

Quantity in Stock:

Product Code: LA-18R

Qty:

Email me when Back-In-Stock

Description

Recertification Protocol

Labconco Freezone 18L FreezeDryer System inc Bulk Tray Dryer & Vacuum Pump

The Labconco Freezone 18 Liter Console Freeze Dry System is a powerful laboratory lyophilizer with ice holding capacity for light to moderate sample loads. It includes the bulk tray dryer and the attached 6 port drying chamber (as shown) and Rebuilt Edwards Vacuum Pump. Sample containers, such as flasks, are the only additional components necessary for a complete system. Catalog #s 7755042 and 7806031. This freeze dryer system includes all the vacuum hardware needed.

All of our equipment is fully tested to perform at factory specifications before being shipped.

INCLUDED:
The Labconco Freezone 18L FreezeDryer System inc Bulk Tray Dryer includes:

> New Edwards RV12 Vacuum Pump
> Vacuum Hardware, Mist Filter, Pump Oil
> Power Cords
> Operator's Manual
> Full 180 Day Parts and Labor Warranty

Labconco Freezone 18 Liter Freeze Dry System Specifications

Ice Holding Capacity	18L
Lowest Temperature	-50C
Water Removal Over 24 Hours	10L
Manifold	Stoppering Tray Dryer w/ 6 Port Manifold
Electrical Requirements	230V, 60Hz, 9A
Vacuum Pump Displacement Required	195L/min
Dimensions (W x D x H)	32.2 x 28 x 36.3 in
Weight	425 lbs
Conformance	CE

Request a Formal Quote

Recertification Inspection Protocol

Inspect the display for pixel clarity and brightness issues; replace any dim or defective pixels to ensure optimal visual quality.
Test each button for responsiveness, resistance, and continuity; replace any buttons that show wear or unresponsiveness.
Check the acrylic/glass lid for structural integrity, looking for cracks or chips; replace if any damage is found.
Examine all external gasket seals for elasticity, cracks, or tears; replace compromised seals with OEM-approved parts.
Remove and replace all manifold ports with new OEM parts, ensuring proper fit and sealing to maintain system integrity.
Drain and replace the oil, verifying the new oil’s viscosity and particulate levels fall within operational standards.
Conduct diagnostic checks on all PCB test points, replacing any malfunctioning components to maintain circuit integrity.
Inspect all internal rubber connections and gaskets for cracks or brittleness; replace compromised parts as needed.
Disassemble and clean the condenser coils and fan assembly to remove dust; replace worn components to ensure efficiency.
Confirm the start capacitor for the refrigeration system meets the manufacturer-specified capacitance range; replace if readings deviate.
Test and calibrate all internal sensors and safety switches, ensuring accurate readings and replacing any faulty components.
Verify displayed temperatures by cross-referencing with independent calibrated probes; recalibrate the system if discrepancies are detected.
Check vacuum pressure using an independent gauge, aiming for ~0.40 mbar; address any leaks or inefficiencies affecting vacuum levels.
Confirm the system achieves and maintains low temperatures (~-50°C or ~-80°C) using certified measurement tools; troubleshoot as necessary.
Inspect all external surfaces, labels, and interfaces for cosmetic wear; address any scratches, blemishes, or visible signs of damage.

Technician Inspection and Recertification Checklist

The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment

Task	Completed?	Remarks?
Inspect display for pixel issues and replace if needed	Completed
Test button functionality and replace any defective buttons	Completed
Examine door seal and lock functionality; replace if compromised	Completed
Conduct PCB test point diagnostics and replace as needed	Completed
Verify compressor and internal fan functionality	Completed
Confirm temperature probe accuracy with NIST-traceable probe	Completed
Inspect all wiring for frays, tears, or breakages	Completed
Test start capacitor capacitance range; replace if needed	Completed
Replace all internal filters and clean condenser fins	Completed
Test alarm battery for full functionality	Completed
Run 72-hour test with data recorder to confirm stable temperatures	Completed
Conduct cosmetic inspection and address any issues	Completed