 |
 |
 |
|
HP Agilent 1100 HPLC System with Diode Array Detector & Fluorescence Detector
The HP Agilent 1100 HPLC System guarantees the most efficient mixing and pulse-free solvent delivery for consistently fast and accurate results. The system’s optimized design using a quaternary pump allows variable stroke volumes for stable solvent flow. This electronically activated inlet valve runs synchronous to the pistons to eliminate vapor formation in volatile solvent, making the HP Agilent 1100 both remarkably easy-to-use and maintenance-free. It also features a high-speed proportioning valve and a pre-configured degasser, which allow convenient low-pressure mixing and a large solvent choice flexibility. The HPLC System’s vacuum degasser ensures reduced operating costs without the use of helium and optimum instrument performance. The HP Agilent 1100 Diode Array Detector verifies separation quality with peak purity, multiple signals, and spectral libraries during your analytical quantification, offering an extended wavelength range with the highest sensitivity. The VWD and diode array detectors allow for automated wavelength verification for performance tracking. The HP Agilent 1100’s temperature management system ensures optimum baseline stability-even under rough ambient conditions. This detector features superb illumination using combined deuterium and tungsten lamps for the highest intensity and lowest detection limit from 190 to 950 nm, 1024 diodes and 1-nm slit for highest spectral resolution. The programmable slit helps you explore the spectral landscape for faster sample characterization, ensuring higher sensitivity or lower baseline noise as necessary on the 1100. Slit settings can be stored and reported from 1 – 16 nm with raw data for GLP traceability. The HP Agilent 1100 Fluorescence Detector brings high-sensitivity and selection through simultaneous multi-wavelength detection. This easy-to-use detector provides quantitative data and fluorescence spectra from a single run. The FD's spectral information can be used for rapid method optimization and verification of separation quality. The unit can be operated with a hand-held controller or computer running Clarity software. The HPLC System features extensive diagnostics with compatible data analysis software for on-site and remote trouble-shooting. All of our equipment is fully tested to perform at factory specifications before being shipped.
The HP Agilent 1100 HPLC System w/ DAD & FLD Detectors includes:
- > G1311A Quat Pump (Binary Pump Available)
- > G1313A Autosampler (G1329A Thermal Autosampler and G1330B Thermal Unit available for an additional cost)
- > G1315A DAD Detector
- > G1321A FLD Detector
- > G1316A Column Compartment
- > G1322A Degasser (G1379A Degasser Available)
- > Windows 10 Professional 64-Bit Data Station with Flatscreen Monitor
- > Chemstation version 4.3 software installed
- > All Power Cords
- > Can/Crossover Cables
- > Agilent G1369 Lan Interface Card
- > Solvent Tubing
- > Bottles, Caps and Solvent Filters
- > Capillaries
- > Full 90 Day Parts and Labor Warranty
Below is a List of Diagnostic Tests Performed On This System
- Filter Test: The test moves the filter into the light path and measures the relative absorbance in the filter position.
- Dark Current Test: The test measures the dark current from the detector optic.
- Holmium Oxide Test: The test measures the Holmium spectrum from the built-in Holmium filter. The spectrum is evaluated for peaks at different wavelengths.
- Lamp Intensity Test: The test verifies functionality of the UV lamp at various wavelengths.
- Wavelength Intensity Test: The test confirms the accuracy of wavelengths measured.
- Baseline Noise Test: The test measures the amount of baseline noise drift identified by the detector.
- Pressure Test: The pressure test is a quick, built-in test designed to demonstrate the pressure tightness (up to 400 bar) of the system.
- Leak Test: The leak test is a built-in troubleshooting designed to demonstrate the leak-tightness of the pump.
- Thermostat Test: Evaluates the cooling and heating performance of the two Peltier elements.
- Injector Steps: Performs each movement of the sampling sequence under manual control. This is useful for confirming autosampler functionality.
- 4 Peak Test (Isocratic Standard): Standard test published by Agilent to confirm complete functionality of the 1100 HPLC System.
HP Agilent 1100 HPLC System Specifications
|
Type
|
Specification
|
|
Detection type
|
Double-beam photometer
|
|
Light Source
|
Deuterium lamp
|
|
Wavelength Range
|
190 - 600 nm
|
Short term noise (ASTM) Single
and Multi-Wavelength
|
± 0.75 × 10-5AU at 254 nm
|
|
Drift
|
3 × 10-4AU/hr at 254 nm
|
Linear Absorbance range
|
> 2 AU (5%) upper limit
|
|
Wavelength accuracy
|
± 1 nm
|
|
Slit width
|
1, 2, 4 , 8, 16 nm
|
|
Band Width
|
6.5 nm typical
|
|
Diode Width
|
< 1 nm
|
|
Flow Cells
|
Standard: 14-µl volume, 10-mm
cell path length and 40 bar
(588 psi) pressure maximum
High pressure: 14-µl volume,
10-mm cell path length and
400 bar (5880 psi) pressure
maximum
Micro: 1-µl volume, 5-mm cell
path length and 40 bar (588 psi)
pressure maximum
Semimicro: 5-µl volume, 6-mm
cell path length and 40 bar
(588 psi) pressure maximum
|
|
Control and Data Evaluation
|
Agilent ChemStation for LC
|
|
Analog Outputs
|
Recorder/integrator: 100 mV or 1 V,
output range 0.001 – 2 AU, two
outputs
|
|
Communications
|
Controller-area network (CAN), GPIB,
RS-232C, APG Remote: ready, start,
stop and shut-down signals, LAN
optional
|
|
Safety and Maintenance
|
Extensive diagnostics, error detection
and display (through control module
and ChemStation), leak detection, safe
leak handling, leak output signal for
shutdown of pumping system. Low
voltages in major maintenance areas.
|
|
GLP Features
|
Early maintenance feedback (EMF) for
continuous tracking of instrument
usage in terms of lamp burn time with
user-settable limits and feedback
messages. Electronic records of
maintenance and errors. Verification of
wavelength accuracy with built-in
holmium oxide filter.
|
|
Housing
|
All Materials recyclable
|
|
Computer Specifications
|
|
Model
|
Dell Optiplex 7010 Desktop PC
|
|
Processor
|
Intel Core i5-3470 Processor 3.2GHz
|
|
Ram
|
8GB
|
|
Hard Drive
|
250GB Internal SSD
|
|
Operating System
|
Windows 10 Professional, 64bit
|
HP Agilent 1100 Series HPLC System Operator's Manual
 Click Here to View all the Technical Specs for the HP Agilent 1100 System
Our technicians decontaminate and clean equipment upon arrival at our facility and upon your purchase to create a neutral environment for your labs use.
Preliminary testing is then conducted on our equipment to identify potential defects. Upon completion, we replace all faulty and/or under-performing parts with original manufacturer parts that perform up to specification.
Any parts known to fail or malfunction on the piece of equipment are removed and replaced to insure the extended lifetime of your equipment.
Any necessary preventative maintenance is performed alongside repairs, so your purchase will be ready to go as soon as it arrives.
All of the electronics and boards are tested for proper function and response by our industry trained technicians. Any electronic deficiencies detected are immediately repaired.
Final testing cycles ensure your equipment performs fully at manufacturer specifications, guaranteeing you receive a properly working product ready for use.
Once we finish our rigorous testing and decontamination procedures, your order will be packaged to best protect it during shipment and will include delivery insurance.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Every product we offer undergoes a rigorous inspection process to verify that all manufacturer specifications are met. All of the electronics and boards are tested for proper function, and any necessary preventative maintenance is performed alongside repairs by our industry trained technicians. Our primary goal is to offer products that are as close to new as possible at an affordable price.
All Lab Equipment is Fully Recertified and Tested
Most Pieces Ship within 2 to 5 Business Days
All Products Come with a Standard Warranty
Trained Customer and Technical Support
Industry Leading Overall Customer Satisfaction
We love shopping at Marshall Scientific! Great products, prices, and performance. Marshall Scientific provides 'tried and true' equipment at a fraction of original purchase price. I always shop here first!
Meg W. / Stanford University
Easy to find what you need with clear specs, website ordering was simple, equipment arrived quickly, very well packaged and working as expected! I couldn't ask for more, I'll definitely use them again!
A. Bradley / Honeywell
They do a very high quality job worth every penny they charge. Customer service is fantastic, they can always be reached by phone or email, and the staff are very knowledgeable and ready to help.
Igor P. / University of Maryland
Click Here to View Our Other Testimonials →
|
|
|
|
|
|
|
