 |
 |
 |
|
Fisherbrand Isotemp GPD 02 Water Bath
Temperature Range
Ambient to 90°C
Temperature Uniformity
± 0.2C at 37C
- Advanced digital controller with user-friendly icon-based navigation
- Three programmable temperature presets for convenient operation
- Audible alarms and adjustable high-temperature protection for safety
- Low-fluid protection helps safeguard the bath and samples
- Stainless steel chamber and galvanized steel body for durability
- Protective coating provides strong resistance to corrosion
- Redesigned hinge design supports open-lid operation and easy removal
- Compatible with optional Thermal Beads as an alternative heating medium
- Compact design conserves valuable laboratory bench space
The Fisherbrand Isotemp GPD 02 Water Bath is a compact 2-liter system engineered to deliver reliable temperature control for industrial, clinical, pharmaceutical, and biomedical applications. Featuring an advanced digital controller with user-friendly icon-based navigation, the Fisherbrand Isotemp GPD 02 Water Bath ensures precise operation with three programmable temperature presets and adjustable high-temperature protection. Audible alarms and built-in low-fluid protection safeguard both the unit and valuable samples.
Constructed with a durable stainless steel chamber and galvanized steel body with protective coating, the Fisherbrand Isotemp GPD 02 Water Bath offers strong resistance to corrosion and is easy to clean for long-term use. A redesigned hinge design allows for secure open-lid positioning and effortless lid removal, adding convenience to routine operation. Compatible with optional Thermal Beads for alternative heating media, the Fisherbrand Isotemp GPD 02 Water Bath combines compact design, safety features, and consistent performance to meet the demands of modern laboratories. All of our equipment will be fully tested to perform at factory specifications before being shipped.
The Fisherbrand Isotemp GPD 02 Water Bath
includes:
- > Bath Lid
- > Calibration
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Fisherbrand Isotemp GPD 02 Water Bath
Specifications
|
Temperature Range
|
Ambient to 90°C
|
|
Temperature Uniformity
|
± 0.2C at 37C
|
|
Temperature Stability
|
± 0.1C at 37C
|
|
Control
|
Digital
|
|
Capacity
|
2L (0.53 gal.)
|
|
Heater Wattage
|
200W
|
|
Bath Dimensions (W x D x H)
|
6.1 x 5.4 x 5.9 in. (15.5 x 13.8 x 15 cm)
|
|
Overall Dimensions (W x D x H)
|
7.8 x 9.1 x 9.2 in. (19.9 x 23 x 23.3 cm)
|
|
Electrical Requirements
|
100-115V, 50/60Hz, 1.6A
|
- Confirm power supply and PCB are outputting stable, correct voltages across all essential circuits to ensure reliable operation
- Inspect the display for any dim, flickering, or dead pixels, replacing any compromised sections to maintain full clarity and accurate readouts
- Verify that all buttons, knobs, and switches are functioning properly, providing precise and responsive control across all settings
- Conduct a thorough inspection of the water reservoir for any holes, rust, or other structural damage that may impact its integrity
- Fill the reservoir with water, checking closely for any external or internal leaks that could affect performance
- Examine the lid for any signs of wear or damage, replacing hinges and handles if necessary to ensure a secure and proper seal
- Inspect for any internal leaks originating from the water reservoir, confirming the unit’s internal plumbing integrity
- Conduct a comprehensive inspection of internal wiring for any breakages, tears, or wear; replace any underperforming or damaged components to maintain safe operation
- Examine internal insulation for signs of burns, breaks, or deterioration, replacing as needed to ensure thermal efficiency and safety
- Confirm that all feet are intact and that the bath sits level and balanced on a flat surface to prevent movement or instability
- Calibrate both temperature accuracy and uniformity using a NIST-traceable temperature probe, verifying compliance with specification standards
- Perform a detailed cosmetic inspection to confirm that all external surfaces and finishes meet aesthetic and quality standards
Technician Inspection and Recertification Checklist: Water Bath
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Confirm power supply and PCB output stable, correct voltages across circuits
|
Completed
|
|
|
Inspect display for dim, flickering, or dead pixels; replace for clarity
|
Completed
|
|
|
Verify functionality of all buttons, knobs, and switches for responsive control
|
Completed
|
|
|
Inspect water reservoir for holes, rust, or structural damage
|
Completed
|
|
|
Fill reservoir with water; check for external or internal leaks
|
Completed
|
|
|
Examine lid for wear or damage; replace hinges or handles as needed
|
Completed
|
|
|
Inspect for internal leaks from water reservoir to confirm plumbing integrity
|
Completed
|
|
|
Check internal wiring for damage; replace underperforming components for safety
|
Completed
|
|
|
Examine internal insulation for burns, breaks, or deterioration; replace as needed
|
Completed
|
|
|
Confirm feet are intact and bath is balanced on flat surface
|
Completed
|
|
|
Calibrate temperature accuracy and uniformity with NIST-traceable probe
|
Completed
|
|
|
Perform cosmetic inspection to confirm quality of external surfaces and finishes
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
