 |
 |
 |
 |
Biotek Synergy HT Microplate Reader
The Biotek Synergy HT is a single-channel absorbance, fluorescence, and luminescence microplate reader. It is computer-controlled using BioTek’s Gen5 or KC4 PC software for all operations including data reduction and analysis. The Synergy HT is robot accessible and compatible with BioTek’s BioStack Microplate Stacker. When making fluorescence determinations, the Synergy HT uses a tungsten quartz
halogen lamp with interference filters for wavelength specificity in conjunction with a
photomultiplier (PMT) tube detector. Luminescence is measured by the low-noise PMT detector through an empty filter
position in the Emission filter wheel. Absorbance measurements are made by switching to a xenon flash lamp and a
monochromator for wavelength selection.
The Synergy HT has a 4-Zone temperature control from 4°C over ambient to 50°C and supports the reading of 6-, 12-, 24-, 48-, 96-, and 384-well microplates with standard 128 x 86 mm geometry. Internal plate shaking is supported to ensure that reagents are properly mixed prior to reading.
Included with the Biotek Synergy HT Microplate Reader:
Includes:
> Windows 10 Data Station with Pre-Loaded Gen5 PC Software> Operator's Manual > Interface Cable > Full 90 Day Part and Labor Warranty
Biotek Synergy HT Multimode Microplate Reader Specifications
Microplate
Capacity
|
Standard 6-,
12-, 24-, 48-, 96-, 384-well microplates
Max Plate
Height:
Luminescence/Fluorescence
modes: plates up to 1.25” (31.75 mm) high
Absorbance mode: plates up to 0.8” (20.30 mm) high
|
Dimensions (D
x W x H)
|
16 x 15 x 10
in
40.6 cm x 38
cm x 25.4 cm
|
Weight
|
38 lb. (17
kg)
|
Environment
|
Operational
temperature 18º to 40°C
|
Light Source
|
Absorbance: Xe
flash light source
Fluorescence:
Tungsten quartz halogen
|
Humidity
|
10% to 85%
relative humidity (non-condensing)
|
Power Consumption
|
100 VA max,
130 VA max with injectors
|
Incubation
|
Temperature
control range from 4º over ambient to 50ºC
Temperature
variation ± 0.50°C across the plate @ 37°C (250 µL per well with the plate
sealed)
|
Plate Shaking
|
Low, Medium,
High and Variable shaking speeds. Shake time is programmable by the user
|
Read Modes
|
Normal, Rapid
and Sweep
|
Absorbance
Measurement Range
|
0.000 to
4.000 OD
|
Absorbance
Accuracy
|
2.000 to
2.500 OD ± 3.0% ± 0.010 OD Normal and Rapid modes, 96- and 384-well plates
|
Absorbance
Linearity
|
2.000 to
2.500 OD ± 3.0% Normal and Rapid modes, 96- and 384-well plates
|
Absorbance
Repeatability
|
0.000 to
2.000 OD ± 1.0% ± 0.005 OD Normal and Rapid modes, 96- and 384-well plates
|
Fluorescence
Read Timing
|
Excitation
Filter: 485/20 nm
Emission
Filter: 528/20 nm
96-well read:
89 sec
384-well read:
275 sec
|
Fluorescence
Sensitivity
|
5mm probe: 10
pg/ml solution of Sodium Fluorescein in PBS
3mm probe: 20
pg/ml solution of Sodium Fluorescein in PBS
1.5mm probe: 40
pg/ml solution of Sodium Fluorescein in PBS
|
Time Resolved
Fluorescence
|
Delay 0 or 20
µs to 16000 µs
Integration
interval 20 to 16000 µs
Times
adjustable in 10 µs increments
|
Computer Specifications
|
Processor
|
Intel I5-4300U CPU
|
Ram
|
16.0 GB
|
Brand
|
Hewlett-Packard
|
Hard drive
|
240GB Solid State Drive
|
Operating System
|
Windows 10 64-Bit
|
BioTek Synergy HT Manual
Our technicians decontaminate and clean equipment upon arrival at our facility and upon your purchase to create a neutral environment for your labs use.
Preliminary testing is then conducted on our equipment to identify potential defects. Upon completion, we replace all faulty and/or under-performing parts with original manufacturer parts that perform up to specification.
Any parts known to fail or malfunction on the piece of equipment are removed and replaced to insure the extended lifetime of your equipment.
Any necessary preventative maintenance is performed alongside repairs, so your purchase will be ready to go as soon as it arrives.
All of the electronics and boards are tested for proper function and response by our industry trained technicians. Any electronic deficiencies detected are immediately repaired.
Final testing cycles ensure your equipment performs fully at manufacturer specifications, guaranteeing you receive a properly working product ready for use.
Once we finish our rigorous testing and decontamination procedures, your order will be packaged to best protect it during shipment and will include delivery insurance.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Every product we offer undergoes a rigorous inspection process to verify that all manufacturer specifications are met. All of the electronics and boards are tested for proper function, and any necessary preventative maintenance is performed alongside repairs by our industry trained technicians. Our primary goal is to offer products that are as close to new as possible at an affordable price.
All Lab Equipment is Fully Recertified and Tested
Most Pieces Ship within 2 to 5 Business Days
All Products Come with a Standard Warranty
Trained Customer and Technical Support
Industry Leading Overall Customer Satisfaction
We love shopping at Marshall Scientific! Great products, prices, and performance. Marshall Scientific provides 'tried and true' equipment at a fraction of original purchase price. I always shop here first!
Meg W. / Stanford University
Easy to find what you need with clear specs, website ordering was simple, equipment arrived quickly, very well packaged and working as expected! I couldn't ask for more, I'll definitely use them again!
A. Bradley / Honeywell
They do a very high quality job worth every penny they charge. Customer service is fantastic, they can always be reached by phone or email, and the staff are very knowledgeable and ready to help.
Igor P. / University of Maryland
Click Here to View Our Other Testimonials →
|
|
 |
 |
 |
 |

|