 |
 |
 |
 |
Agilent 1200 HPLC G1321A Fluorescence Detector
The Agilent 1200 HPLC G1321A Fluorescence Detector brings high-sensitivity and selection through simultaneous multi-wavelength detection. This easy-to-use detector provides quantitative data and fluorescence spectra from a single run. The FD's spectral information can be used for rapid method optimization and verification of separation quality.
All of our equipment is fully tested to perform at factory
specifications before being shipped.
Included with the Agilent 1200 HPLC G1321A FLD Detector: Includes: > Firmware version A.07.02 (Can be changed upon request) > Calibration Report > 8μl Flow Cell > Lab Advisor Diagnostic Report > Lan Cable / Power Cord > Operator's Manual > Full 90 Day Parts and Labor Warranty
Agilent 1200 HPLC G1321A Fluorescence Detector Specifications
Detection Type
|
Multi-signal fluorescence detector with rapid on-line scanning
capabilities and spectral data analysis
|
Performance Specifications
|
10 fg Anthracene, Ex=250 nm, Em=400 nm* RAMAN single wavelength (H2O)
> 500 with Ex=350 nm, Em=397 nm, dark value 450 nm, standard flow cell
time constant=4 seconds (8 seconds responsetime) RAMAN dual wavelength (H2O)
> 300 with Ex=350 nm, Em=397 nm, dark value 450 nm, standard flow cell
time constant=4 seconds (8 seconds responsetime)
|
Light source
|
Xenon Flash Lamp, normal mode 20 W, economy mode 5 W
|
Pulse frequency
|
296 Hz for single signal mode 74 Hz for spectral mode
|
Excitation Monochromator
|
Range: 200 nm - 700 nm and zero-order Bandwidth: 20 nm (fixed)
Monochromator:concave holographic grating, F/1.6, blaze: 300 nm
|
Emission Monochromator
|
Range: 280 nm - 900 nm and zero-order Bandwidth: 20 nm (fixed)
Monochromator:concave holographic grating, F/1.6, blaze: 400 nm
|
Reference System:
|
in-line excitation measurement
|
Timetable programing
|
up to 4 signal wavelengths, response time, PMT Gain, baseline
behavior (append, free, zero), spectral parameters
|
Spectrum acquisition:
|
Excitation or Emission spectra Scan speed: 28 ms per datapoint (e.g.
0.6 s/spectrum 200-400 nm, 10 nm step) Step size: 1-20 nm Spectra storage:
All
|
Wavelength characteristic
|
Repeatability+/- 0.2 nm Accuracy+/- 3 nm setting
|
Flow cells
|
Standard: 8 µl volume and 20 bar (2 MPa) pressure maximum, quartz
Optional: Fluorescence cuvette for offline spectroscopic measurements with 1
ml syringe, 8 µl volume, quartz
|
Control and data evaluation
|
Agilent ChemStation for LC, Agilent Instant Pilot G4208A or Agilent
Control Module G1323B with limited spectral data analysis and printing of
spectra
|
Communications
|
Controller-area network (CAN), GPIB, RS-232C, LAN, APG Remote: ready,
start, stop and shut-down signals
|
HP Agilent G1321A FLD Manual Click Here to View all the Technical Specs for the G1321A FLD
Our technicians decontaminate and clean equipment upon arrival at our facility and upon your purchase to create a neutral environment for your labs use.
Preliminary testing is then conducted on our equipment to identify potential defects. Upon completion, we replace all faulty and/or under-performing parts with original manufacturer parts that perform up to specification.
Any parts known to fail or malfunction on the piece of equipment are removed and replaced to insure the extended lifetime of your equipment.
Any necessary preventative maintenance is performed alongside repairs, so your purchase will be ready to go as soon as it arrives.
All of the electronics and boards are tested for proper function and response by our industry trained technicians. Any electronic deficiencies detected are immediately repaired.
Final testing cycles ensure your equipment performs fully at manufacturer specifications, guaranteeing you receive a properly working product ready for use.
Once we finish our rigorous testing and decontamination procedures, your order will be packaged to best protect it during shipment and will include delivery insurance.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Every product we offer undergoes a rigorous inspection process to verify that all manufacturer specifications are met. All of the electronics and boards are tested for proper function, and any necessary preventative maintenance is performed alongside repairs by our industry trained technicians. Our primary goal is to offer products that are as close to new as possible at an affordable price.
All Lab Equipment is Fully Recertified and Tested
Most Pieces Ship within 2 to 5 Business Days
All Products Come with a Standard Warranty
Trained Customer and Technical Support
Industry Leading Overall Customer Satisfaction
We love shopping at Marshall Scientific! Great products, prices, and performance. Marshall Scientific provides 'tried and true' equipment at a fraction of original purchase price. I always shop here first!
Meg W. / Stanford University
Easy to find what you need with clear specs, website ordering was simple, equipment arrived quickly, very well packaged and working as expected! I couldn't ask for more, I'll definitely use them again!
A. Bradley / Honeywell
They do a very high quality job worth every penny they charge. Customer service is fantastic, they can always be reached by phone or email, and the staff are very knowledgeable and ready to help.
Igor P. / University of Maryland
Click Here to View Our Other Testimonials →
|
|
 |
 |
 |
 |

|